Search results

  1. C

    Need help from real machinists

    Al it sounds like some 316 stainless And sounds work hardened with stainless I usually drill it 10 to 20 percent less than 1018 steel and increase feed by 5 to 10 percent if I have a good way to feed it consistently. Otherwise slow it all down maybe 30 to 50 percent and keep tool cutting or...
  2. C

    Please recommend a magnetic base for an Interapid 300 series dial indicator.

    I use all of the ones mentioned and I use the noga's the most I have repaired a few of them even the noga. What I like about my noga's I can get new fine adjust heads And the nobs are easy or quick to make replacements. The big one I can hang off the headstock for dialing in the barrel in...
  3. C

    Norma 6 Dasher

    Just my thinking but if you want truer ammo your going to want to fire form anyway. Right?
  4. C

    Tuners what do you think about my first one?

    Thanks for all the info and input. I appreciate it.
  5. C

    Tuners what do you think about my first one?

    That's a good thing In my case I need the excuses to go shooting
  6. C

    Tuners what do you think about my first one?

    That's funny
  7. C

    Tuners what do you think about my first one?

    A example of the thread (My gauge)
  8. C

    Tuners what do you think about my first one?

    I learned I should have drilled and taped it at finish diameter then turn a taper on it after because the end mill I was spotfacing it with grabed it and spun it in my 5C collet (On the tool post I didn't have tight enough) and chewed up my tapered surface. So I put a radius in there. I don't...
  9. C

    Tuners what do you think about my first one?

    Thanks Jerry How will it hasten the barrels end of life By making it more accurate so it is shot more?
  10. C

    Tuners what do you think about my first one?

    I was asking Jackie about tuners a while back and made me one because I needed or wanted a 13/16-32 thread so what do you guys think ? bad idea ? Like don't like Interested in your thoughts Thanks Ya I used someone else's rubber
  11. C

    Good Floating Reamer Holder

    Im listening would you please share your methods? I'm very interested. I feel best with dialing in the throat and muzzle
  12. C

    Ultimate front spider.

    Thanks it has a very light blue synthetic oil in it with moly. Just a little full so it is right above the high mark when runing.
  13. C

    Ultimate front spider.

    Yes it's being set up for chamber and thread for a savage action. In this setup I'm turning the shank down close to 1.0625 them I'll move up closer for the finish diameter and chamber and thread.
  14. C

    Ultimate front spider.

    It was fully machined or had the the screw holes in it and I turned it down just past them. And skim cut each face surface, diameters and bore.
  15. C

    Ultimate front spider.

    just to help lock them in place probably not necessary but maybe just psychological. I usually use two on each and just finger tight. Also can make very small adjustments by tightening them slitely more on initial dial in.
  16. C

    Ultimate front spider.

    I ordered it from eBay it is a back plate for a adjust true chuck with the D1-4 mount. From Discount_machine
  17. C

    Ultimate front spider.

    Just got my d1-4 back plate and made my replacement.
  18. C

    Good Floating Reamer Holder

    Thanks Greg. the input is much appreciated
  19. C

    Good Floating Reamer Holder

    I think rock a lot of it was for the oil industry
  20. C

    Good Floating Reamer Holder

    Thanks that brings back memories of twenty years ago when I first started programming and operating cnc mills with a simple cad program we were making coring bits with diamonds and a carbide,nickle,molybdenum matrix. a part I have in the machine now about 300 pounds of 4140 when I started
Back
Top