remington 700 action?????

S

skeetlee

Active member
I was hoping someone could clear up a little info for me pertaining to a rem 700 bolt action, and there feed ramps. I may buy a rem 700 varmint in 223 from a friend of mine, and if i do i am not so sure i will leave it a 223. I haven't ever been particularly found of the 223, and i have a deep desire to own a 22-250ai. i was hoping i could buy a second bolt from kiff with a 308 bolt face. Were i need the help or clarification is that i once read that you cant use a 308 bolt in an action that came with a 223 bolt size bolt face. Something about the feed ramps being different or something?? So i need to know if i can put a 308 bolt in this action if i purchase it? I dont probably want to change anything permanent on this 223 bolt as the barrel thats on the rifle shoots very well now that i have cut some of it off and re-crowned it. I thought i might just open the bolt face thats on it but like i said i hate to change this bolt, plus i am sure i would have to have a new extractor installed so it might just be better to buy a hole new bolt from kiff? I dont know. I haven't ever played around much like this with these actions. thanks Lee
 
The bolts interchange and single feed will work, the factory magazine will not. The 'rails' on a .223 are too close to allow a 308 case to pass, the 'rails' of a .308 are too wide to retain a .223 case.

It doesn't make economical sense to buy a .223 to make a 308 based rifle...
 
So we are just talking about a 15$ follower then? thats not a big deal. i thought there was an issue with the feed ramp or something like that. If i do this it will be a switch barrel hunting/prairie dog rifle. thanks Lee
 
It works great if you only load one at a time. I switch from large bolt face and back to small bolt face often. I have an extra Remington bolt and a PTG bolt. Obviously I have to reset head-space every time I change barrels, but you have to do that anyway.

I block off the magazine - so only can load one at a time.

KG
 
If you are still looking for a 308 bolt, I have a few, three I think, bolt bodys only with extractors, no ejector or firing pin assembly but you could use that stuff from your old bolt. Email me if you are interested. I think I have extra magazine boxes, followers and springs also.

Jim

Jkob60@msn.com
 
Last edited by a moderator:
I happen to have a few actions lying around waiting for barrels so I snapped a pic for those who might be curious. Besides the width difference point for timing the round when it pops out of the mag, note the 308 has a bevel on the rails and on the top of the action an ejection relief.

rem_700_223_on_bottom_vs_308_on_top.JPG
 
If i end up with this rifle i think ill leave it as it is. Its shooting really well after i recrowned it anyway. I shortened the barrel buy about 4 inches and cut a nice crown, and now it really shoots well! I think an old remington 40x stock with a single shot floor follower would be ideal. Heck i might even buy it and give it to my dad as a gift. As far as the 308 bolt. Over on snipers hide they have a group buy on stiller actions so i picked up a new stiller tac30 repeater with a 308 bolt for 760 bucks shipped. Kinda hard to beat that. I will do my 22-250AI project with this action. I have wanted a 22-250AI for over two years, so now its time!! I appreciate the help fellas as always. This is a good group of fellas to say the least. I would like to ask if anyone has a spare Remington 40x stock you could part with? I would be interested in that. I know i can get one at Numrich, but with those you just dont always know what kind of shape the stock will be in when it arrives. thanks again, Lee
 
You must log in or register to reply here.
Back
Top