Search results

  1. C

    Falling Blocks

    falling blocks Thank You for the replies. Where is Al Shaver? Michael
  2. C

    Falling Blocks

    Could someone refer me to a smith that could chamber a Hall Falling block Action? Thank You Michael Taner
  3. C

    Getting Harder To Travel To Matches

    Gas and travel Louis also living in the great state of ca. I would move too but I have family. Hope I can travel to Visailia in October. regards Michael Taner
  4. C

    220 russian

    iS THE 220 RUSSIAN CASE BECOMING SCARCE ?
  5. C

    Chrome Moly vs Stainless steel

    A chrome Moly Action I know this is about barrels but I had to share. I am getting a chrome Moly DS action. I will get it in a few weeks. Regards Michael
  6. C

    Inside neck lubing with MOLY

    Molyslide I use Neco Molyslide 800-451-3550 I use a Q tip and a toothbrush and nylon brush Stu Harvey showed me this one. Chuck up a case. . USE THIS stuff very very sparingly. As case spins run brush dabbed in molyslide in the neck. Run toothbrush over neck. Turn. Clean up with. A tiny...
  7. C

    Sure name in the forum?

    name change Hello this is Michael I would change my name but do not know how to go about it? Help
  8. C

    Australian 322

    322 It is a 6ppc in a 13.5 twist bartlien barrel
  9. C

    Australian 322

    322 Yes this is H-322 manufactured in Australia and packaged in USA by Hogedon. Mchael
  10. C

    Australian 322

    Hello All I am beginning to work on a jug of 322 Australian 39288 50026. I would appreciate any load suggestions you have. What is the hot end for a 68 gr. Boat tail 7/10 ogive? Is it temperature sensitive? Thank You for any feedback. I would like to know the date is was made? 13.5 twist
  11. C

    c;hrome Moly Actions

    What are the differences between a chrome Moly vs a stainless steel action? Are there any features to a chrome Moly that make it worth while?
  12. C

    Starting in Benchrest

    223 and group Hello, I just want to say that I shot a 223 for a season and a half. The club let me shoot with them. They were very helpful. I finally got my first real benchrest rifle. I think a you might do well at a group match. Michael
  13. C

    contact number

    Does anybody have a contact mail or phone for Lou Murdica? Thank you Michael
  14. C

    Broken March Scope

    Would anyone know where to send MARCH SCOPE FOR REPAIR Thank You Michael
  15. C

    Blc 1

    I have a jug of blc1. Will it work in a 6PPC? What would be a good starting load. It is an old powder and probably not as strong as it once was. It smells fine. NOt acrid. Any suggestions please? Thanks Michael
  16. C

    shooting 10x

    Hello All, I have been shooting R-10x this winter. It shoots good in the 40 to 50 degree range. SO far groups are small low 2s a few 1s. I have used primarily 27.5,6,7. My question is has anybody been shooting hot. Like 28.5 plus? What are the results of your practice. Thank You Michael
  17. C

    Lt-30

    Has anyone used LT30 IN A ppc. I am going to try it today. What were your results. thank you Michael
  18. C

    BLC-1 powder

    Who has used blc1 in a cartridge? How would it work in a PPC? It is still stable and hot. Any feedback would be appreciated. Michael Taner
  19. C

    Brass turning cutting fluid

    With a toothbrush and neck brush With a toothbrush and neck brush I use NECO Molyslide paste. It has worked real well on the mandrel. Michael
  20. C

    contact for terry lenard

    Is terry still making stocks? Michael
Back
Top